Command (Subsystem)
SOURce subsystem
| CURR | Sets the AC current upper limit |
|---|---|
| CURR:OFFS | Sets the DC current upper limit |
| CURR:PEAK | Sets the peak limit of the positive electric potential |
| CURR:PEAK:LOW | Sets the peak limit of the negative electric potential |
| CURR:PROT:OCP2:TIME | Sets the time that must elapse after the internal semiconductor protection is activated before an alarm is generated |
| CURR:PROT:STAT | Action that is performed when the current limit is exceeded |
| CURR:PROT:TRIP:TIME | Sets the time until the protection function trips when the current limit is exceeded |
| FREQ | Sets the frequency |
| FREQ:LIM | Sets the frequency upper limit |
| FREQ:LIM:LOW | Sets the frequency lower limit |
| FREQ:MODE | Sets the trigger function control of the frequency setting |
| FREQ:SYNC | Turns the synchronization function on and off |
| FREQ:SYNC:PHASE:DEL | Sets the synchronization delay phase angle of the synchronization function |
| FREQ:TRIG | Sets the frequency that will be set when a trigger is received |
| VOLT | Sets the AC voltage |
| VOLT:LIM | Sets the AC voltage upper limit |
| VOLT:LIM:LOW | Sets the AC voltage lower limit |
| VOLT:MODE | Sets the trigger function control of the AC voltage setting |
| VOLT:OFFS | Sets the DC voltage |
| VOLT:OFFS:LIM | Sets the DC voltage upper limit |
| VOLT:OFFS:LIM:LOW | Sets the DC voltage lower limit |
| VOLT:OFFS:MODE | Sets the trigger function control of the DC voltage setting |
| VOLT:OFFS:PROT:LEV | Sets the OVP value to use to judge averaged voltage measurements |
| VOLT:OFFS:PROT:LEV:LOW | Sets the UVP value to use to judge averaged voltage measurements |
| VOLT:OFFS:TRIG | Sets the DC voltage that will be set when a trigger is received |
| VOLT:PROT:LEV | Sets the OVP value used to judge rms voltage measurements |
| VOLT:PROT:LEV:LOW | Sets the UVP value used to judge rms voltage measurements |
| VOLT:RANG | Sets the voltage range |
| VOLT:TRIG | Sets the AC voltage that will be set when a trigger is received |
| VOLT:VCC | Sets the internal Vcc voltage |
| VOLT:VCC:MODE | Sets the Vcc operating condition |
| WAVE:BANK | Specifies the number of the waveform bank that you want to execute |
| WAVE:BANK:TRIG | Sets the number of the waveform bank that will be set when a trigger is received |
| WAVE:BANK:MODE | Sets the trigger function control of the number of the waveform bank |
| WAVE:BANK:TYPE | Queries the output waveform type |
| WAVE:EDIT:PCL | Sets the special waveform to the sine wave or a peak-clipped waveform, and sets the crest factor |
| WAVE:EDIT:USER:DATA:POIN | Sets a user-defined waveform |
| WAVE:EDIT:SIN | Sets the special waveform to the sine wave |
SOURce subsystem
(Single-phase, three-wire output/ Three-phase output)
| CURR{1|2|3} | Sets the AC current upper limit of each phase |
|---|---|
| CURR{1|2|3}:OFFS | Sets the DC current upper limit of each phase |
| CURR{1|2|3}:PEAK | Sets the peak limit of the positive electric potential of each phase |
| CURR{1|2|3}:PEAK:LOW | Sets the peak limit of the negative electric potential of each phase |
| VOLT{1|2|3} | Sets the AC voltage of each phase |
| VOLT{1|2|3}:TRIG | Sets the AC voltage of each phase that will be set when a trigger is received |
| VOLT:LINE | Sets the AC line voltage |
| VOLT{1|2|3}:OFFS | Sets the DC voltage of each phase |
| VOLT{1|2|3}:OFFS:TRIG | Sets the DC voltage of each phase that will be set when a trigger is received |
| VOLT:OFFS:LINE | Sets the DC line voltage (2P05-PCR-LE only) |
| WAVE{1|2|3}:EDIT:USER:DATA:POIN | Sets a user-defined waveform of each phase |
SOURce subsystem (Analog signal operation)
| FUNC:SOUR | Sets the signal source (EX05-PCR-LE only) |
|---|---|
| VOLT:EXT:SOUR | Sets the signal source (EX06-PCR-LE only) |
AC Power Supply PCR-LE series