OUTP:IMP:LEV
Sets the output impedance in terms of resistance.
This command is valid when the output impedance is on (OUTP:IMP ON).
Command
OUTPut:IMPedance:LEVel {<numeric>|MINimum|MAXimum}
OUTPut:IMPedance:LEVel? [{MINimum|MAXimum}]
Parameter
| Value | Value | L range (default) | H range (default) | |
| PCR500LE PCR1000LE PCR2000LE PCR3000LE PCR4000LE PCR6000LE PCR9000LE |
0.04 to 4.0 (0.04) 0.02 to 2.0 (0.02) 0.01 to 1.0 (0.01) 0.00667 to 0.667 (0.00667) 0.005 to 0.5 (0.005) 0.00333 to 0.333 (0.00333) 0.00222 to 0.222 (0.00222) |
0.16 to 16.0 (0.16) 0.08 to 8.0 (0.08) 0.04 to 4.0 (0.04) 0.02667 to 2.667 (0.02667) 0.02 to 2.0 (0.02) 0.01333 to 1.333 (0.01333) 0.00889 to 0.889 (0.00889) |
||
| PCR6000LE2 | Single-phase output 0.00333 to 0.333 (0.00333) Single-phase three-wire output, Three-phase output 0.01 to 1.0(0.01) |
Single-phase output 0.01333 to 1.333 (0.01333) Single-phase three-wire output, Three-phase output 0.04 to 4.0(0.04) |
||
| PCR9000LE2 | Single-phase output 0.00222 to 0.222 (0.00222) Single-phase three-wire output, Three-phase output 0.00667 to 0.667 (0.00667) |
Single-phase output 0.00889 to 0.889 (0.00889) Single-phase three-wire output, Three-phase output 0.02667 to 2.667(2.667) |
||
| PCR12000LE2 | Single-phase output 0.00167 to 0.167 (0.00167) Single-phase three-wire output, Three-phase output 0.005 to 0.5 (0.005) |
Single-phase output 0.00667 to 0.667 (0.00667) Single-phase three-wire output, Three-phase output 0.02 to 2.0(0.02) |
||
| PCR18000LE2 | Single-phase output 0.00111 to 0.111 (0.00111) Single-phase three-wire output, Three-phase output 0.00333 to 0.333 (0.00333) |
Single-phase output 0.00444 to 0.444 (0.00444) Single-phase three-wire output, Three-phase output 0.01333 to 1.333(0.01333) |
||
| PCR27000LE2 | Single-phase output 0.000741 to 0.0741 (0.000741) Single-phase three-wire output, Three-phase output 0.00222 to 0.222 (0.00222) |
Single-phase output 0.00296 to 0.296 (0.00296) Single-phase three-wire output, Three-phase output 0.00889 to 0.889(0.00889) |
||
| Unit | OHM | |||
For the setting that is applied when *RST is sent, see this table
For the setting that is applied when *RST is sent, see this table
For the setting that is applied when *RST is sent, see this table
Response
Returns the output impedance (in terms of resistance) in NR3 format in response to OUTP:IMP:LEV?.
AC Power Supply PCR-LE series