AC power supply PCR-LE2 series
Specifications
Option Specifications
TYP: These are typical values. These values do not guarantee the performance of the PCR-LE2 Series.
Communication interface (GPIB/ USB/ LAN)
The specifications of the IB05-PCR-LE (GPIB), US05-PCR-LE (USB), and LN05-PCR-LE (LAN) interface boards are provided below.
GPIB |
Complies with IEEE Std 488.1-1987 SH1, AH1, T6, L4, SR1, RL1, PP0, DC1, DT1, C0, and E1 24-pin connector (receptacle) |
|
|
Message terminator |
LF or EOI during reception, LF + EOI during transmission |
Primary address |
1 to 30 |
|
USB |
Complies with the USB 2.0 specifications. Data rate: 12 Mbps (full speed), Socket B type |
|
|
Message terminator |
LF or EOM during reception, LF + EOM during transmission |
Device class |
Complies with the USBTMC-USB488 device class specifications |
|
LAN |
IEEE 802.3100Base-TX/10Base-T Ethernet Complies with the LXI Specification Ver.1.3 Class C, Data rate: 100 Mbps (Auto negotiation, full speed) AUTO MDIX function IPv4, RJ-45 connector (Category 5; use a straight cable.) |
|
|
Communication protocol |
VXI-11/HiSLIP/SCPI-RAW |
Message terminator |
VXI-11, HiSLIP: LF or END during reception, LF + END during transmission SCPI-RAW: LF |
Controlling the Output Using External Analog Signals
The following specifications specify the comprehensive performance achieved when the Analog Interface is installed in the PCR-LE2 AC power supply. Other specifications not given here comply with those for the PCR-LE2 AC power supply.
|
EX05-PCR-LE |
EX06-PCR-LE |
|
Input terminal |
Maximum allowable input voltage |
±15 V |
|
Type |
BNC |
||
Input impedance |
10 kΩ ±10 % |
||
Isolation voltage |
±63 Vpeak |
||
Input voltage range |
0 V to 1.5 Vrms sine wave |
0 Vdc to +10 Vdc |
|
Input frequency range*1 |
1 Hz to 2k Hz (Sine wave) 1 Hz to 200 Hz (Rectangular wave) DC |
--- |
|
Frequency characteristics |
DC to 5k Hz: -3dB or less with respect to 200 Hz (On input of sine wave of 0.5 Vrms) |
--- |
|
Voltage amplification ratio (L, H range) |
100x, 200x (Outputs a 0 Vac to 150 Vac/0 Vac to 300 Vac with respect to an input of 0 Vac to 1.5 Vac) |
15x, 30x (Outputs a 0 Vac to 150 Vac/0 Vac to 300 Vac with respect to an input of 0 Vdc to 10 Vdc) |
|
Frequency setting range |
--- |
1 Hz to 999.9 Hz |
|
Output voltage distortion ratio*2 |
PCR-LE specifications + 0.5 % or less |
||
Output voltage temperature coefficient |
PCR-LE specifications + 200 ppm/°C(TYP) |
||
Insulation resistance
|
Between input (BNC) and chassi, input(BNC) and input, input (BNC) and output |
500 Vdc, 30 MΩ or more |
|
Withstand voltage |
Between input (BNC) and output, input (BNC) and output |
500 Vac for 1 minute |
|
Status signal output*3 |
OUTPUT ON STATUS |
Turns on when the output is on. |
|
ALARM STATUS |
Turns on when an alarm/trouble is detected. |
||
BUSY STATUS |
Turns on when the busy status. |
||
OOR STATUS |
Turns on when the current limit is exceeded and when overload occurs. |
||
External control*4 |
OUTPUT CONTROL*5 |
Output on with a low level signal/Output on with a high level signal. |
|
SEQ RUN*5 |
Run the sequence with a low level signal/Run the sequence with a high level signal. |
||
ALARM CLR*5 |
Alarm clear with a low level signal/Alarm clearwith a high level signal. |
||
SHUT DOWN*6 |
Output off with an open circuit/Output off with a short circuit |
*1. The measurable range of voltage, current, and power is DC and 1 Hz to 999.9 Hz
Set the frequency according to the input waveform period.
*2. When DC current is applied for EX06-PCR-LE or when a sine wave with distortion ratio of 0.1 % or less is applied for EX05-PCR-LE.
*3. Open collector outputs of photocouplers (30 Vdc, 8 mAmax.)
*4. Set the logic using CONFIG settings. The internal circuit is pulled up to 12 V through 1.3 kΩ.
*5. HIGH: Input terminal voltage of 11 V to 12 V or open; LOW: Input terminal voltage of 0 V to 1 V
*6. Open: Open or input terminal voltage of 11 V to 12 V; Short: Input terminal voltage of 0 V to 1 V
AC power supply PCR-LE2 series
Specifications