Default settings
The settings after an *RST command, *RCL command, MEAS:<meter_fn>? command, and power-on are indicated in Table 4.
| *RCL: | Recalls the contents saved to the memory (0 to 3). | |
| *RST: | Initializes the settings to their factory default values. However, the contents of the three memories remain unchanged. | |
| MEAS:<meter_fn>?: | Initializes a portion of the settings to default, starts the measurement, and queries the data. |
| Setup Item | Setting | Unit | Function | |||
| *RST | *RCL | MEAS?*1 | At power-om | |||
| IMP:AVER:MOV:COUNT | 1 | *2 | 1 | *3 | - | Moving average count |
| IMP:CURR:AC | 0 | *4 | Arms | Measureing AC current | ||
| IMP:CURR:AC:RAT | 10 | 10 | % | Measuring AC current (as a percentage of the load current) | ||
| IMP:CURR:AC:FREQ | 20 000 | 20 000 | Hz | Measuring frequency | ||
| IMP:CURR:PULS:TRAN | 0.01 m | 0.01 m | s | Pulse transition time of the interrupt current | ||
| IMP:CURR:PULS:WIDT | 0.01 | 0.01 | s | Pulse width of the interrupt current | ||
| IMP:CURR:PULS:DEPT:RAT | 100 | 100 | % | Pulse depth of the interrupt current (ass a percentage of the load current) | ||
| IMP:CURR:PULS:DEPT | 0 | 0 | A | Pulse depth of the interrupt current | ||
| IMP:SAMP:POS | 0.06 m | 0.06 m | s | Sampling start position | ||
| IMP:SAMP:REG | 0.03 m | 0.03 m | s | Sampling range | ||
| VOLT:PROT:LOW | -2 | -2 | V | Voltage sensing undervoltage protection | ||
| VOLT:PROT:LOW:DEL | 4 | No change | s | Voltage sensing undervoltage protection delay time | ||
| METH | ACIM | - | Impedance measurement method ACIM: AC Impedance Method |
|||
| INP | OFF | No change | OFF | - | Load on/off | |
| INP:SST:RISE | 0 | *2 | *3 | S | Soft start rising edge | |
| INP:SST:FALL | 0 | S | Soft start falling edge | |||
| INP:SENS:VOLT | 1 | - | Voltage measurement channel | |||
| INP:SENS:CURR | 1 | - | Current measurement channel | |||
| SOUR:CURR | 0 | A | PLZ-4W load current | |||
| SOUR:CURR:EXT | 0 | A | Current of the external electronic load | |||
| SOUR:CURR:RANG | HIGH | - | PLZ-4W load current range | |||
| SOUR:VOLT | 0 | V | PLZ-4W voltage | |||
| SOUR:VOLT:RANG | HIGH | - | PLZ-4W voltage range | |||
| SOUR:VOLT:PROT:LOW | -1 | V | PLZ-4W undervoltage protection | |||
| SOUR:POW:PROT | *5 | W | PLZ-4W overpower protection | |||
| FORM:BORD | NORM | No change | NORM | - | Data transmission/recording mode NORM:Big Endian |
|
| FORM:PAGE:STAR | 0 | 0 | s | Start point of the data to be transferred | ||
| FORM:PAGE:LENG | 0.1 | 0.1 | s | Length of the ddata to be transferred | ||
| TRIG:COUN TRIG:SEQ2:COUN |
1 | 1 | 1 | - | Trigger count | |
| TRIG:TIM TRIG:SEQ2:TIM |
0.01 | 0.01 | 0.01 | s | Trigger hold off | |
| TRIG:SOUR TRIG:SEQ2:SOUR |
IMM | IMM | IMM | - | Trigger source IMM: Immediate |
|
*1. MEAS:<meter_fn>?
*2. Depends on the settings in the memory.
*3. Settings immediately before the power switch was turned off.
*4. Present DC load current setting (SOUR:CURR) *1/10
*5. Depends on the rated load current of the PLZ-4W Series.